Rack and Pinion

  • Step 1
    Select the Series of High
    Precision Reducer for Servo
    Motor from Product Line Up
  • Step 2
    Select the
    Backlash
  • Step 3
    Select the Linkage Method
    (High Precision Reducer for
    Servo Motor and Device)
  • Step 4
    Enter User Values
  • Step 5
    Enter Driving
    Pattern and Condition
Step1 Select the Series of High Precision Reducer for Servo Motor from product line up

Please select the Series of High Precision Reducer for Servo Motor

Click here for the differences in each series
  • Step 1
    Select the Series of High
    Precision Reducer for Servo
    Motor from Product Line Up
  • Step 2
    Select the
    Backlash
  • Step 3
    Select the Linkage Method
    (High Precision Reducer for
    Servo Motor and Device)
  • Step 4
    Enter User Values
  • Step 5
    Enter Driving
    Pattern and Condition
Step2 Select the Backlash

Select the Backlash of output shaft

If you want to go back to the previous page, click the “Back” button at the bottom left.

<Reference>
Output shaft 1 round(360 deg.)/360=1 deg.
1 deg./60=1 arcmin, 1 deg./20=3 arcmin, 1 deg./4=15 arcmin, 1 deg./2=30 arcmin
* Low Backlash (30 to 60 arcmin) accuracy would be deferent by reduction ratio

  • Step 1
    Select the Series of High
    Precision Reducer for Servo
    Motor from Product Line Up
  • Step 2
    Select the
    Backlash
  • Step 3
    Select the Linkage Method
    (High Precision Reducer for
    Servo Motor and Device)
  • Step 4
    Enter User Values
  • Step 5
    Enter Driving
    Pattern and Condition
Step3 Select the Linkage Method (High Precision Reducer for Servo Motor and Device)

Select Linkage Method (High Precision Reducer for Servo Motor and Device)

If you want to go back to the previous page, click the “Back” button at the bottom left.

  • Step 1
    Select the Series of High
    Precision Reducer for Servo
    Motor from Product Line Up
  • Step 2
    Select the
    Backlash
  • Step 3
    Select the Linkage Method
    (High Precision Reducer for
    Servo Motor and Device)
  • Step 4
    Enter User Values
  • Step 5
    Enter Driving
    Pattern and Condition
※Sample Image
Step4 Enter User Values

If you want to go back to the previous page, click the “Back” button at the bottom left.

Moving Speed V =
Weight of the Work M1 = kg
Weight of Rack
and Table
M2 =
kg
P.C.D. of Pinion
D1 =
mm
P.C.D. of Driven Side
Sprocket
(Timing Pulley, Gear)
D2 =
mm
P.C.D. of Drive Side
Sprocket
(Timing Pulley, Gear)
D3 =
mm
Inclination Angle θ = °
Friction Coefficient
of the Guide
μ =
Rated Rotational
Speed of
Servo Motor
N1 =
r/min
Service Factor Sf =
※Select the coefficient
Correction Coefficient
of Moment of Inertia by
Operating Conditions
C=
Coefficient according
to Linkage Method
K1 =
Coefficient according
to Load Position
K2 =
Coefficient according
to Linkage Method
fb =
Coefficient according
to Load Level
fw =
O.H.L. Load Position
Before using the High Precision Reducer for Servo Motor
Calculation Selection Tool.
Please read carefully before using the High Precision Reducer for Servo Motor Calculation Selection Tool.

When using the High Precision Reducer for Servo Motor Calculation Selection Tool (hereafter referred to as "this Calculation Selection Tool") provided on the website by Nissei Corporation(hereafter referred to as "we"), please be sure to read the notes and disclaimers below and use it only if you agree to all the terms. If you disagree, you may not be able to use this Calculation Selection Tool.

Notes & Disclaimers

  1. The calculation results from this calculation selection tool are all reference values and we do not guarantee the contents. Please use it as a reference when selecting a product. When using the product, be sure to recalculate and check if it meets the conditions of use.
  2. We do not take any responsibility for any damage, disadvantage or trouble caused to users or third parties by using this Calculation Selection Tool or its calculation results.
  3. Contents of the Calculation Selection Tool are subject to change without notice. We take no responsibility for any loss of opportunity due to the changes of the Calculation Selection Tool.